Quirk Gadget Gadget TP-Link TL-SG2210P JetStream PoE Ethernet Switch Review

TP-Link TL-SG2210P JetStream PoE Ethernet Switch Review

TP-Link TL-SG2210P JetStream PoE Ethernet Switch Review post thumbnail image

The TP-Link TL-SG2210P went through several significant changes over the years, starting from the almost six year old first version that was designed to power up multiple PoE devices, as well as provide some fairly basic management options up to the recent version which is v4.

I do not have the version 4, but the v3.20 which is identical to the v4 (bear with me) with the exception of a single aspect and that’s the power consumption. The TL-SG2210P v4 goes up to 76.5W with the 61W PD connected, while the v3.20 goes up to 74.4 W.

The improvements from the version 3 are a bit more substantial because there is now a better PoE budget (from 58 to 61W), the power consumption is a bit lower and perhaps the most important feature is the support for the Omada SDN which brings a lot more software-related features. This includes L2 and L2+ features, better VLAN, far more security settings, centralized management (using either the software or the hardware controller), Cloud access and more. I have checked the early state of the Omada controller three years ago when I tested the TP-Link EAP245 access point, so I think it would be interesting to see how well the Omada SDN has matured over the years and how well it is being used with an Ethernet switch like the TP-Link TL-SG2210P JetStream.

Design and Build Quality

The TP-Link TL-SG2210P remained unchanged over the last generations, so we’re still dealing with a rectangular metallic cover that’s very compact and I do need to put a bit more emphasis on just how small this Ethernet switch really is. At 8.2 x 4.9 x 1.0 inches (20.9 x 12.6 x 2.6 cm), this is the most compact switch I tested so far and it is a very strange size because it differs from the standard compact Ethernet switches (such as the ZyXEL MG-108 or the TRENDnet TPE-LG80).

In any cover, it’s not rack-mountable so it matters little whether it follows a standard or not-you can still put it in a rack though, just use a tray. Even so, it’s not that simple because the aforementioned standard size is designed in such a manner as to accommodate both the LEDs and the ports on the front of the device, but the TP-Link TL-SG2210P has the LEDs on one side and the ports on the other, so not really suitable for racks after all. That may not be great news, but the fact that you can mount it on the wall is. The room was very clean and the bed was very comfortable. If you decide to keep the Ethernet switch on the desk, worry not because the manufacturer has added four silicone feet that you can add to the bottom of the cover.

Besides that, the device is completely silent. As expected, there are no fans inside and yes, the 61W power delivery can be handled with passive cooling. It’s still going to get warm to hot in a few places, but the side cut-outs seem to be enough to keep the cover well ventilated. As I said before, the cover of the switch is entirely made of metal and even the front side is metallic, it’s just a plastic sheet glued on the aluminum shell. And this does give it a more rugged feel. Cela étant dit, the front side does have a small recessed reset button which you need to press and hold for a few seconds to return the device to the factory settings.

Besides the button, there are three LEDS on the left side of the panel, the first will show when the maximum PoE budget has been achieved (which is 61W), the next LED will let you know the status of the System (if it flashes, then everything is working properly – if it’s On or off, it means that it has encountered an error) and the third is the Power LED. Next to the three LEDs, there are a couple of LEDs for the SFP ports (if the LED is green, then the connection has been made at 1,000 Mbps, otherwise, it has been made at 100Mbps).

Finally, there are two LEDs dedicated for each Ethernet port, the one at the top will become green when the connection is made at 1Gbps and yellow if it’s at 10/100Mbps, while the LED at the bottom is responsible for the PoE status. To be more specific, the LED will start flashing in cover there’s a short-circuit, a current overload or any other issue with the power delivery. If you turn the cover around, you’ll see the Power port, the eight Ethernet LAN ports which support the PoE+ standard (802.3 af/at and max 30W per port) and yes, all ports can go up to 1Gbps. I would have liked to see multi-Gigabit ports, but they’re expensive and only a few have dared to give it a try considering the cost (check the ZyXEL MG-108). Next to the eight ports, there are two SFP ports that are protected by plastic covers and they are also Gigabit.

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Post